Showing posts with label lamp. Show all posts
Showing posts with label lamp. Show all posts

Wednesday, September 11, 2013

Hg Lamp to a Powerful UV Light Source

I got myself some UV-curable solder mask for my PCB workshop, and as soon as i got it, i discovered that my UV artwork transfer box is totally incapable to activate the UV paint and cure it. I began searching the net for powerful UV lamps, and then it hit me: Some months ago i uploaded a theory regarding the Cold and Hot cathode discharge lamps. During my research for these lamps i found out that they can provide directly visible light (lamps without internal coating), or they produce UV radiation. The lamps that produce UV radiation have an extra coating on their internal surface which glows when excited by the UV rays, thus producing light!

Hacking a Hg Lamp to a Powerful UV Light Source
Read More..

Wednesday, May 29, 2013

6V lamp Flasher circuit Diagram

This is 6V lamp flasher circuit diagram.You can use this circuit for your various purposes.or you can use this for your 6V moter bike

Read More..

Monday, May 13, 2013

Dark activated LED or Lamp Flasher

This circuit adopts the rather unusual Bowes/White emitter coupled multivibrator circuit. The oscillation frequency is about 1Hz and is set by C1 value. The LED starts flashing when the photo resistor is scarcely illuminated. The onset of flashing can be set by trimming R2.
Dark-activated Flasher
Read More..

Saturday, April 13, 2013

12V Flourescent Lamp Inverter

Fluorescent tubes use a methods much less vitality than incandescent lamps and fluorescent tubes final a perfect deal lengthyer as neatly. Other benefits are diffuse, glare-free lighting and low heat output. For these motives, fluorescent lights is the natural possibility in commercial and retail buildings, workshops and factories. For battery-powered lights, fluorescent milds are additionally the primary choice because of their excessive effectivity. The main drawback with running fluorescent lights from battery power is that an inverter is required to drive the tubes.

Circuit diagram:

\"12-volt-flourescent-lamp-Inverter-circuit\"
12V Fluorescent Lamp Inverter Circuit Diagram
Fig.1: two switch-mode circuits are concerned here: the DC-DC inverter involving IC1, Q1 & Q2 and the fluoro tube powerr which converts excessive voltage DC to AC by the use of IC3 and Q3 & Q4 in a totem-pole circuit.
Inverter efficiency then transforms the key issue. There are many industrial 12V-operated fluorescent lamps available which use 15W and 20W tubes. However, it is uncommon to look one which drives them to full brilliance. For example, a typical commercial twin 20W fluorescent lamp working from 12V draws 980mA or 11.8W. Ignoring losses in the fluorescent tube pressurer itself, it means that every tube is simplest equipped with 5.9W of power which is considerably not up to their 20W rating. So whereas the lamps do use 20W tubes, the gentle output is smartly below par.

Warning:

This circuit generates in excess of 300V DC which can be lethal. Construction will have to only be attempted via these experimenced with mains-level voltages and safety processs.
 
 
http://www.ecircuitslab.com
Read More..

Thursday, April 11, 2013

Battery Powered Night Lamp

Ultra-low current drawing 1.5V battery supply

This circuit is usable as a Night Lamp when a wall mains socket is not available to plug-in an ever running small neon lamp device. In order to ensure minimum battery consumption, one 1.5V cell is used, and a simple voltage doubler drives a pulsating ultra-bright LED: current drawing is less than 500µA. An optional Photo resistor will switch-off the circuit in daylight or when room lamps illuminate, allowing further current economy. 
 
This device will run for about 3 months continuously on an ordinary AA sized cell or for around 6 months on an alkaline type cell but, adding the Photo resistor circuitry, running time will be doubled or, very likely, triplicated.

Battery-Powered Night Lamp Circuit diagram :

Battery-powered Night Lamp Circuit diagram 
Parts:

R1,R2___________1M   1/4W Resistors
R3_____________47K 1/4W Resistor (optional: see Notes)
R4____________Photo resistor (any type, optional: see Notes)

C1____________100nF 63V Polyester Capacitor
C2____________220µF 25V Electrolytic Capacitor

D1______________LED Red 10mm. Ultra-bright (see Notes)
D2___________1N5819 40V 1A Schottky-barrier Diode (see Notes)

IC1____________7555 or TS555CN CMos Timer IC

B1_____________1.5V Battery (AA or AAA cell etc.)

Circuit operation:

IC1 generates a square wave at about 4Hz frequency. C2 & D2 form a voltage doubler, necessary to raise the battery voltage to a peak value able to drive the LED.

Notes:
  • IC1 must be a CMos type: only these devices can safely operate at 1.5V supply or less.
  • If you are not needing Photo resistor operation, omit R3 & R4 and connect pin 4 of IC1 to positive supply.
  • Ordinary LEDs can be used, but light intensity will be poor.
  • An ordinary 1N4148 type diode can be used instead of the 1N5819 Schottky-barrier type diode, but LED intensity will be reduced due to the higher voltage drop.
  • Any Schottky-barrier type diode can be used in place of the 1N5819, e.g. the BAT46, rated @ 100V 150mA.

Source :  http://www.ecircuitslab.com/2011/06/battery-powered-night-lamp-circuit.html
Read More..

Monday, April 8, 2013

Brightness Controller Lamp Circuit

This is a design for control the brightness lamp. The circuit can be used to control the brightness of low power incandescent lamps. The circuit is based on IC NE555. This is the figure of the circuit.


The IC is wired as an astable multi vibrator with variable duty cycle. The output of IC is connected to the base of transistor Q1.The Q1 drives the lamp. The duty cycle of the multi vibrator can be varied by varying the POT R4.As a result, the brightness of the lamp varies according to the position of the POT R4.The same circuit can be also used for speed control of small DC motors. The IC1 must be mounted on a holder. The lamp L1 can be a 6V / 200 mA lamp. The switch S1 can be SPST ON/OFF switch.

Read More..