Showing posts with label inverter. Show all posts
Showing posts with label inverter. Show all posts

Monday, December 23, 2013

Cheap 12V to 220V Inverter

Even though today’s electrical appliances are increasingly often self-powered, especially the portable ones you carry around when camping or holidaying in summer, you do still sometimes need a source of 230 V AC - and while we’re about it, why not at a frequency close to that of the mains? As long as the power required from such a source remains relatively low - here we’ve chosen 30 VA - it’s very easy to build an inverter with simple, cheap components that many electronics hobbyists may even already have.

Though it is possible to build a more powerful circuit, the complexity caused by the very heavy currents to be handled on the low-voltage side leads to circuits that would be out of place in this summer issue. Let’s not forget, for example, that just to get a meager 1 amp at 230 VAC, the battery primary side would have to handle more than 20 ADC!. The circuit diagram of our project is easy to follow. A classic 555 timer chip, identified as IC1, is configured as an astable multivibrator at a frequency close to 100 Hz, which can be adjusted accurately by means of potentiometer P1.

Cheap 12V to 220V Inverter Circuit diagram:


As the mark/space ratio (duty factor) of the 555 output is a long way from being 1:1 (50%), it is used to drive a D-type flip-flop produced using a CMOS type 4013 IC. This produces perfect complementary square-wave signals (i.e. in antiphase) on its Q and Q outputs suitable for driving the output power transistors. As the output current available from the CMOS 4013 is very small, Darlington power transistors are used to arrive at the necessary output current. We have chosen MJ3001s from the now defunct Motorola (only as a semi-conductor manufacturer, of course!) which are cheap and readily available, but any equivalent power Darlington could be used.

These drive a 230 V to 2 × 9 V center-tapped transformer used ‘backwards’ to produce the 230 V output. The presence of the 230 VAC voltage is indicated by a neon light, while a VDR (voltage dependent resistor) type S10K250 or S07K250 clips off the spikes and surges that may appear at the transistor switching points. The output signal this circuit produces is approximately a square wave; only approximately, since it is somewhat distorted by passing through the transformer. Fortunately, it is suitable for the majority of electrical devices it is capable of supplying, whether they be light bulbs, small motors, or power supplies for electronic devices.

PCB layout:
pcb-layout-12-volt-to-230-volt-invertor-circuit-diagram
PCB Layout For Cheap 12V to 220V Inverter Circuit Diagram

Parts List :
Resistors
R1 = 18k?
R2 = 3k3
R3 = 1k
R4,R5 = 1k?5
R6 = VDR S10K250 (or S07K250)
P1 = 100 k potentiometer
Capacitors
C1 = 330nF
C2 = 1000 µF 25V
Semiconductor
T1,T2 = MJ3001
IC1 = 555
IC2 = 4013
Miscellaneous
LA1 = neon light 230 V
F1 = fuse, 5A
TR1 = mains transformer, 2x9V 40VA (see text)
4 solder pins
Note that, even though the circuit is intended and designed for powering by a car battery, i.e. from 12 V, the transformer is specified with a 9 V primary. But at full power you need to allow for a voltage drop of around 3 V between the collector and emitter of the power transistors. This relatively high saturation voltage is in fact a ‘shortcoming’ common to all devices in Darlington configuration, which actually consists of two transistors in one case. We’re suggesting a PCB design to make it easy to construct this project; as the component overlay shows, the PCB only carries the low-power, low-voltage components.

The Darlington transistors should be fitted onto a finned anodized aluminum heat-sink using the standard insulating accessories of mica washers and shouldered washers, as their collectors are connected to the metal cans and would otherwise be short-circuited. An output power of 30 VA implies a current consumption of the order of 3 A from the 12 V battery at the ‘primary side’. So the wires connecting the collectors of the MJ3001s [1] T1 and T2 to the transformer primary, the emitters of T1 and T2 to the battery negative terminal, and the battery positive terminal to the transformer primary will need to have a minimum cross-sectional area of 2 mm2 so as to minimize voltage drop.

The transformer can be any 230 V to 2 × 9 V type, with an E/I iron core or toroidal, rated at around 40 VA. Properly constructed on the board shown here, the circuit should work at once, the only adjustment being to set the output to a frequency of 50 Hz with P1. You should keep in minds that the frequency stability of the 555 is fairly poor by today’s standards, so you shouldn’t rely on it to drive your radio-alarm correctly – but is such a device very useful or indeed desirable to have on holiday anyway? Watch out too for the fact that the output voltage of this inverter is just as dangerous as the mains from your domestic power sockets.

So you need to apply just the same safety rules! Also, the project should be enclosed in a sturdy ABS or diecast so no parts can be touched while in operation. The circuit should not be too difficult to adapt to other mains voltages or frequencies, for example 110 V, 115 V or 127 V, 60 Hz. The AC voltage requires a transformer with a different primary voltage (which here becomes the secondary), and the frequency, some adjusting of P1 and possibly minor changes to the values of timing components R1 and C1 on the 555.

Source: http://www.ecircuitslab.com/2011/08/cheap-12v-to-220v-inverter.html
Read More..

Saturday, April 13, 2013

12V Flourescent Lamp Inverter

Fluorescent tubes use a methods much less vitality than incandescent lamps and fluorescent tubes final a perfect deal lengthyer as neatly. Other benefits are diffuse, glare-free lighting and low heat output. For these motives, fluorescent lights is the natural possibility in commercial and retail buildings, workshops and factories. For battery-powered lights, fluorescent milds are additionally the primary choice because of their excessive effectivity. The main drawback with running fluorescent lights from battery power is that an inverter is required to drive the tubes.

Circuit diagram:

\"12-volt-flourescent-lamp-Inverter-circuit\"
12V Fluorescent Lamp Inverter Circuit Diagram
Fig.1: two switch-mode circuits are concerned here: the DC-DC inverter involving IC1, Q1 & Q2 and the fluoro tube powerr which converts excessive voltage DC to AC by the use of IC3 and Q3 & Q4 in a totem-pole circuit.
Inverter efficiency then transforms the key issue. There are many industrial 12V-operated fluorescent lamps available which use 15W and 20W tubes. However, it is uncommon to look one which drives them to full brilliance. For example, a typical commercial twin 20W fluorescent lamp working from 12V draws 980mA or 11.8W. Ignoring losses in the fluorescent tube pressurer itself, it means that every tube is simplest equipped with 5.9W of power which is considerably not up to their 20W rating. So whereas the lamps do use 20W tubes, the gentle output is smartly below par.

Warning:

This circuit generates in excess of 300V DC which can be lethal. Construction will have to only be attempted via these experimenced with mains-level voltages and safety processs.
 
 
http://www.ecircuitslab.com
Read More..

Sunday, April 7, 2013

Simple Inverter with Two Transistors

The series below is a simple inverter circuit that will change the voltage of 12v dc to 220v ac, with use drive transistor 32 as its tip.
Inverter circuit is very simple and easy to assemble and is perfect for just starting to learn to assemble electronic circuits, you can use the transformer 2A to produce about 20 watts output. Do not forget to install coolers in its transistors. good luck.
Simple Inverter with Two Transistors

Read More..

Thursday, April 4, 2013

How to Calculate and Match an Inverter Circuit with Battery and Transformer

Making an inverter all by you can be definitely lot of fun. However if the results are not satisfactory can completely spoil the whole purpose of the project. Installing and configuring the various inverter parameter like the battery and the transformer to with the actual assembled circuit needs special care and attention for deriving optimal results from the assembly. The article broadly discusses how to calculate and match a battery and transformer wit the relevant circuit and also enlightens regarding the possible faults that might be encountered and the respective troubleshooting procedures.
The article enlightens the many newcomers with some of the important clues, which might be helpful while configuring an inverter circuit with the battery and the transformer, so that efficient and optimal results can be achieved.

Configuring Inverter Parameters

While making an inverter, two points must be broadly taken into account – the transformer must be rated twice the maximum load that is expected to be used with the inverter and the battery must be rated at 1/4 more than the transformer ratings.

For example, if the inverter is expected to work at 12 volts, with maximum loads of 200 watts, the transformer must be rated at least 500 watts, corresponding to 40 plus amperage, roughly (dividing 500 by 12), and the battery in turn must be rated at = ¼ multiplied by 40 = 10, therefore 40 + 10 = 50 AH (minimum).

After procuring all the necessary components as explained above, it would be important to get them checked for compatibility with one another.

Only the battery, which is one the most crucial member, hopefully will not require any prior checking, because the printed rating and the charged voltage conditions should be sufficient to prove its reliability. It is assumed here that the condition of the battery is good and it’s relatively new and “healthy.”

Next comes the transformer, which is another most important component of the inverter, surely needs a thorough technical assessment. It may be done as follows:


The rating of the transformer can be best checked in the reverse order, i.e. by connecting its higher voltage winding to the AC mains input and checking the opposite winding for the specified outputs.

If the current ratings of the lower voltage section are within the maximum limits of a regular multi-tester (DMM), then it may be checked by switching ON the above AC and connecting the meter (set at, say AC 20 Amp) across the relevant winding.


Hold the meter prods connected across the winding terminals for a couple of seconds to get the readings directly on the meter.

If the reading matches with the specified transformer current, or at least is close to it, means your transformer is OK. Lower readings would mean a bad or a wrongly rated transformer winding.

The assembled circuit broadly needs to be checked for proper oscillation outputs across the bases of the power transistors or the mosfets.

This may be done by connecting the circuit to the battery, but without including the transformer initially. The checking should be done using some good frequency meter or if possible using an oscilloscope.
If the above gadgets are not there with you, a crude testing can be performed using a pair of ordinary headphones. Connect the headphone jack to the bases of the relevant power transistors; you should get a strong humming sound in the headphones, confirming a sound functioning of the oscillator stages.

The above confirmations should be enough to prompt you to configure all the sections together.

Connect the transformer to the relevant transistor or the power devices terminals; make sure the power devices are correctly integrated with the oscillator stage.

Finally the battery may be connected to the power inputs of the above configuration, again do not forget to include an appropriately rated FUSE in series with the battery positive.

The output of the transformer now may be attached with the specified maximum load and the power may be switched ON.

If everything’s is wired up correctly, the load should start operating at its full fledged power, if not, then something’s wrong with the circuit stage.

Since the oscillator section was appropriately checked before the final installations, surely the fault may lie with the power device stage.


If the fault is associated with low power outputs, the base resistors may be tweaked for possible faults, or may be reduced by adding parallel resistors to their existing base resistors.


The results may be checked as discussed above, if the results are positive and if you find improvements in the power outputs, the resistors may be further modified as desired, until the expected power output is delivered.


However this may lead to further heating of the devices and due care must be observed to keep them under check by either including cooling fans or increasing the heatsink dimensions.


However if the fault is accompanied with blowing of the fuse would mean a definite short circuit somewhere in the power stage.

The problem may also indicate a wrongly connected power device, a blown-of power device due to a possible shorting between the power device’s output terminals or the any of the terminals that needs to be perfectly kept aloof of each other.

Having explained a few of the above possibilities while configuring an inverter optimally, a thorough knowledge regarding electronic becomes an absolute necessity from the part of the individual who may be involved with the construction, without which the proceeding with the project may somehow get jeopardized.
Read More..